↑ Return to Polyurethane foam guns

Print this Page

MasterFoam Gun Professional Nickel-Plated – Professional nickel plated foam gun

MasterFoam® Gun Professional Nickel-Plated – Nickel plated professional foam gun

Professional gun for one-component polyurethane foam. Nickel-plated steel ergonomic trigger, brass tube and aluminum body. Teflonised brass needle and aluminum body. Non return steel ball. In well maintained and sealed tool and tightly wrapped can, the foam does not stick to the body up to 20 days after locking the needle using the adjustment screw.

  • Teflonised and nickel-plated parts to protect against external influences, easier cleaning and better appearance.
  • Precise dosing
  • Lengthened tube for easy access to the work area
  • Comfortable trigger
  • Ergonomic handle
  • Demountable design for better cleaning
  • Meets the requirements of TÜF Rheinland

Before starting work screw the adjustment screw so that it blocks the trigger. Then screw the prior shaken can with foam on the adapter. Be careful not to exercise too much force when tightening the can. Unscrew the adjustment screw 2-3 turnover and point the nozzle at an empty container for disposal. Extruding a small amount of foam, while adjusting screw flow.  Hold the can always upside down.
In the termination of work for a relatively short time, screw the adjustment screw so as to lock the trigger and seal the needle to the dosing nozzle and leave the can screwed to the gun.
When replacing an empty can with a new one, turn adjustment screw so as to blocks the trigger, unscrew the empty can and immediately screw the new in its place.
When stop operation for a longer period of time, before removing the can from the gun, screw the adjustment screw so as to blocks the trigger of the gun. Then unscrew the can from the adapter and immediately clean the adapter with cleaner for polyurethane foam Great Stuff Pro Gun Cleaner, using the nozzle for hand operating attached to cleaner can. Then remove the tip for handiwork from the nozzle of cleaner can and screw the cleaner can on the gun adapter. Point the gun at the empty vessel for waste unscrew a 4-5 turnover and press the trigger repeatedly to push the required amount of cleaner. Note that in the beginning will be extruded a certain amount of foam. Do not attempt to use this foam in place to work. The gun is completely cleaned when through the nozzle begins to coming out clear cleaner. Screw the adjustment screw completely and stow the gun.
The design of the gun allows full disassembling when needed cleaning of particles that interfere with normal operation. Use only suitable tools for disassembling to protect parts from damage. Give special attention to disassembling, cleaning and installation of seals, ball valve and the end of needle sealed the nozzle. These details are very sensitive to rough mechanical impact and any surface damage will make them unusable. Damaged seals will allow the foam in the gun to contact with atmospheric moisture, which will lead to its cure in the tool. Already solidified in a narrow closed volume foam could not be removed. Well maintained gun can be used for many years.

  • Do not throw or load with weights the gun. This will lead to distortions in the structure and its irreversible damage.
  • Keep the gun on clean and dry place.
  • Never and under any circumstances do not point the gun at a person, animal, or other living organisms. This can lead to serious consequences for their health and life!

 

Package 1 piece in a box
Construction nickel plated steel ergonomic trigger, brass tube and aluminum body, teflonised brass needle and aluminum body; non return steel ball
Color nickel-gray body, trigger and tube, black adapter, black handle
VN:F [1.9.22_1171]
Rating: 10.0/10 (1 vote cast)
VN:F [1.9.22_1171]
Rating: +1 (from 1 vote)
MasterFoam Gun Professional Nickel-Plated - Professional nickel plated foam gun, 10.0 out of 10 based on 1 rating

Permanent link to this article: http://masterlinebg.com/en/?page_id=1802

Flags Widget powered by AB-WebLog.com.