↑ Return to Adhesives

Print this Page

INSTA STIK – Construction adhesive in the form of PU foam

NSTA STIK® MP Fast Cure – Fast curing construction adhesive in the form of PU foam for thermal insulation, plasterboards and other construction materials

Multifunctional fast curing polyurethane adhesive in the form of foam, specially formulated to bond extruded and expanded polystyrene, mineral wool and gypsum board to concrete, masonry, plaster, wood, metal, glass, bitumen, etc.. Can be used for all operations for bonding building materials and cladding, and for masonry with ceramic, aerated concrete or other blocks. Adheres well to horizontal and vertical surfaces. Available in bottles for gun and handwork.

  • Bonding of insulation panels EPS, XPS, MW (rock wool) and others on practical all building substrates including metal, wood, glass and bituminous surfaces.
  • Bonding of insulation panels to each other through chemical bonds to overcome the big unevenness on the base.
  • Bonding of insulation boards without plugging.
  • Bonding of plasterboard directly on the wall or on the supporting structure of metal or wood profiles.
  • Bonding of wooden boards lining the walls and other decorative materials.
  • Bonding of decorative facade elements, without additional load on the base.
  • Bonding of metal, wood, glass and various materials to each other and whether with one another.
  • Bonding of cladding of ceramic tile, gneiss, granite, natural stone, marble and others.
  • Bonding of EPDM waterproofing membranes.
  • Bonding of masonry blocks from practically all known materials.
  • Bonding of ceramic, concrete, bitumen and other roofing tiles
  • Ideal products for building insulation systems in the Alpine method.
  • Filling of small cavities, which requires low expansion foam.
  • Suitable for almost all construction operations associated with bonding, especially when it requires high performance and speed of execution.
  • Not suitable for bonding nylon.
  • Not recommended for bonding substrates treated with gypsum putty or plaster.

  • Fast curing – 3 to 5 minutes.
  • Implementation of the next operation (eg. putty) after 60 minutes.
  • Clean, dust-free installation.
  • Working without noise, vibration and disturbance to the occupants of the building.
  • Does not require water supply and electricity on the site.
  • Low weight, no load basis – many times less weight added to the system compared with conventional adhesives.
  • Compact package – does not require large storage facilities or vehicles.
  • Flexible decision when choosing a package. Vial for gun for large areas and vial for handwork with reusable valve, suitable for small volume work.
  • Extremely easy to transfer on the construction site.
  • Ready to use product, saving time and labor to prepare the adhesive mixture.
  • Can be used repeatedly until exhaustion the entire pack size without loss.
  • Bonding in wet weather conditions.
  • Excellent resistance to water and moisture.
  • High strength of adhesion to many substrates.
  • Possibility for bonding without plugging in solid foundations.
  • Provides chemical bond between materials of synthetic origin – for example, bonding EPS to EPS, etc.
  • Economic efficiency. One pack of 750 ml. can replace about 2 bags of 25 kg. cementitious adhesive.
  • Improves thermal insulation characteristics of thermal insulation systems. Without thermal bridges.
  • Adheres to practicaly all substrates except nylon and most gypsum plasters.
  • 4 to 5 times less time for building thermal insulation system.
  • Incredibly wide application.

Characteristic Unit Value
Appearance Polyurethane foam with a light yellow color
The volume of the adhesive bottle 750 ml. L 45 (about 120 m adhesive line size 2 x 2 cm)
Време след което не лепна min 4 до 5
Tensile adhesion strength of expanded polystyrene (EPS) to:
concrete kN/m2 140
aerated concrete kN/m2 200
ceramic brick kN/m2 205
wood kN/m2 135
steel kN/m2 230
Tensile adhesion strength of extruded polystyrene (XPS) to:
concrete kN/m2 212
aerated concrete kN/m2 185
ceramic brick kN/m2 331
wood kN/m2 370
steel kN/m2 180

CONSUMPTION at a relatively equal footing (average deviation from flatness within 2 cm):

1. Bonding of panels of plasterboard, wood and others of similar size: 13 to 15 m2 depending on the complexity of the geometry of the pre cladding.

2. Bonding of insulation boards EPS, XPS or MW (mineral wool): 8 to 10 m2 – bonding without fusing of board on board.

Note: The difference in the area on which can be stuck drywall or insulation panels is derived from a larger number of thermal insulation boards that are needed to cover the area that could cover one plate plasterboard and the longest line of adhesive needed for gluing on the periphery of each insulation board.

CONSUMPTION in bricklaying with masonry blocks:

Depending on the nature, size and type of masonry blocks of masonry, can be executed different amounts of masonry. In blocks with larger size adhesive are applied in two lines, and in standard single blocks only one adhesive line. With one bottle of 750 ml. could get around 120 m adhesive line size 2 x 2 cm.

CONSUMPTION for bonding roof tiles:

The consumption of the adhesive in this case depends strongly on the geometry of the roof tiles. The adhesive is applied in line with amount to a maximum 2 x 2 cm. on the supporting grid and to points up to a maximum of 2 x 2 cm. of the contact surfaces between the roof tiles on their laps. With one can of 750 ml. could get around 120 m adhesive line size 2 x 2 cm.

Substrate Preparation
Substrates must be sound, dust free, degreased and without other contaminants which may impair adhesion. Unlike polyurethane foam sealing, in this case does not require pre-wetting of the substrate. Swollen old coats of paint or lime plaster must be removed to sound base.
Recommended is unevenness larger than 2 cm. on average, to be compensated in advance with rough plaster or other suitable solution.
It is not recommended that work on the substrates of gypsum plaster or ground coat such as those type substrates continue to emit dust even after repeated cleaning.

Priming
Not required.

Masking of adjacent surfaces
In the event that are working on surfaces that may be contaminated with accidentally stumbled foam, they must be protected with plastic wrap or other suitable tightly cover.

Application of adhesive
Use the attached to the vial protectors of the hands.

Vial for gun
Vigorously shaken for about 30 seconds. Make sure the adjustment screw of the gun is fitted so as to block the trigger of the gun. Screw the can on the adapter of the gun. Turn the can upside down, unscrew the adjustment screw of the gun 2 turnover and extruding a small amount of foam in a container of waste, while adjust the flow with the screw. Apply adhesive line up to a maximum of 2 x 2 cm on one of the bases by pressing the trigger of the gun. It is recommended that the nozzle of the gun is near the base to provide better contact with the foam in its application. The nozzle should be directed at a slight angle against the foam application.

In a short break to work and if the can has unspent foam, do not unscrew it from the gun, just screw adjustment screw. At the end of the nozzle of the gun is possible to form a small amount of hardened foam. Do not remove it to the renewal of work. In the event that nozzle has omission of pressure, the amount of hardened foam, will serve as a barrier to contact with atmospheric moisture.

When renewing the work, shake the can vigorously, remove cured foam from the nozzle (if any) unscrew adjustment screw, extruding a small amount of foam in waste vessel, while setting the foam flow with the screw.

When emptying the can and in case that work should continue, immediately replace it with new. It is recommended that before replacing the vials adjustment screw to turn so that the gun trigger lock to prevent being accidentally pressed and for accident insurance.

Vial for handwork
Vigorously shaken for about 30 seconds. Screw the straw to the valve. Turn the can upside down and point the straw at the base. Apply adhesive line up to a maximum of 2 x 2 cm on one of the bases. By carefully pressing the trigger adjust flow.

Special design and high-tech materials of the nozzle and valve allow repeatedly interrupted the work for an extended period of time (about 2 months after first use, when properly assembled). Immediately after the application of foam, bend the straw as shown in the figure on the left and then join it to the small nozzle above the trigger. In the event that within the area of connection of straw to the small nozzle appear slightly hardened foam is preferably not removed until further use.

In the period of storage after interruption, in the straw will form a translucent composition. This is not a defect. When resume the work, disconnect carefully straw from the smallest nozzle (without exercising excessive force) and if in its end is a solid foam, cut hardened part with the model knife.

Adhesive line
The adhesive is applied on one of the bases for bonding. Given that the adhesive cures upon contact with atmospheric moisture and weather conditions are variable, it is recommended before starting work to test time for the formation of surface skin. Do not allow bonding adhesive after the already formed a skin. Higher humidity means less time for the formation of skin.
When applied to the plate, it is recommended that the adhesive is applied along the entire periphery of about 3-4 inches from the outer edge and an extra in the middle in the form of the letter “W” or three additional adhesive lines. Care must be taken to the adhesive is applied so that after pressing the plate it does not extend beyond it and do not fill gaps.
When applied adhesive on the basis on which will be sticks plate shall be applied vertical adhesive lines distance of approximately 10 cm. apart. Apply adhesive over area which will cover within 3 to a maximum of 5 minutes depending on weather conditions. I will be bonded heavier parts (such as rock wool with density 130 kg/m3), adhesive lines should be at a distance of 5 cm apart.

For bonding of narrow details, use the method of applying adhesive lines.

For bonding of masonry blocks, apply two adhesive lines along the masonry block.

After bonding the details, the glue should cover at least 40% of the area.

Not recommended application of adhesive on the balls.

Bonding
Best results are achieved when working in teams – one worker applied adhesive and one worker sticks and leveling boards.
For independent work, the worker can apply adhesive on three plates, then start bonding the first plate, etc.
After bonding of 5-6 panels, it is advisable to check leveling with lute with a length of 3 meters.
It is important to observe all the rules for building thermal insulation system.

Bridging the large unevenness
If the base has unevenness above average 2 cm is recommended that they be compensated for by boards of different thicknesses.
In particularly large unevenness can be use the method of bonding board to the board. Unlike cementitious adhesives, in this case takes place very strong chemical connection between the panels, which makes the method absolutely acceptable.
In no case should unevenness to compensate with adhesive. Thick applied adhesive will make it difficult or impossible to cure completely and will also lead to increased consumption of material.

Cleaning
Accidental fallen on unprotected surfaces, clothing and equipment foam, can be cleaned before it is hardened with cleaner for unhardened polyurethane foam Great Stuff® Pro Gun Cleaner or MasterClean® PU, observing strict requirements for working with such cleaning product.

Cured polyurethane foam be cleaned only mechanically, such as must be careful not to damage the cleaning surface. Cut the cured foam carefully and as possible near the base. Then scrape off the residue with metallic, elastic and medium sharp tool in a way which will not affect the cleaning base. Pretreatment of the remainder of the cured foam with steam will help her cleaning (make sure that the cleaned surface is resistant to high temperature steam). To avoid the risk of cleaning hardened foam always clean the foam while still fresh.

By end of work or interruption of the application for a longer period of time (over 1 week) and if the can has unused foam, unscrew the can from the gun and clean his valve by using adapter for manual operation with the cleaner. When cleaning, hold the foam can upside down to allow the dissolved foam to drain outside the valve. Otherwise dissolved foam can harden and block the valve.

Immediately after removing and cleaning the can with foam, clean the gun adapter on the outside, then pick up adapter for manual use from the can with cleaner and screw the cleaner on the valve of the gun. Extruding cleaner at an empty vessel to waste with several short clicks of the trigger of the gun. Note that at the first pressing of the trigger, from the gun will be extruded a certain amount of foam. Do not attempt to use this foam for work. When from the gun is sprayed transparent cleaner, cleaning is completed.

When the can will reused again, be sure to check whether there is hardened foam in the valve before you screw it to the gun. In the event that however has hardened foam, remove it carefully to prevent blockage of the adapter of the gun, being careful not to press the valve. At the removal of the cured foam, valve in no case should be directed to the worker. Use safety glasses.

For more details on applications and mode of operation, please contact us or visit the “How to Work with INSTA STIK”.

  • Avoid thick application of the adhesive line. This can lead to unwanted expansion of the foam. If it is applied thick adhesive, stik the detail by sliding it slightly on the base.
  • In the event that bonded insulation board sinks in, do not try to pull out it by hand. Drill the board with the tip of the gun and extruding a small amount of foam that will give the board out.
  • Avoid working on very hot surfaces or in direct sunlight. In warm weather it is advisable to plan work for early morning and late afternoon hours.
  • When operating in cool weather, store cans at room temperature before use.
  • When bonding on a vertical basis, leave the first row to solidify completely (approximately 60 minutes under normal conditions).
  • In wet weather the adhesive hardens faster and under conditions of low humidity curing time increases.
  • Always pre-test the time for the formation of skin before starting work on the next working day.
  • When working with a can for handwork, dispense the adhesive very carefully, as unlike the gun applicator, regulation the flow here is more difficult.
  • After placing a can on the gun which was previously cleaned with cleaner, extruding a small amount of foam in the waste vessel before starting work. It is possible in the gun was left little cleaner which will damage the surfaces of synthetic origin.
  • After work, seal the entire top joint between boards and the wall to prevent the entry of dust and other contaminants.

  • Before starting work, remove all sources of fire, sparks and heat. The can contains a highly flammable gas.
  • Use personal protective equipment for the body, eyes and hands
  • Protect cans from frost or direct sunlight during storage or transportation
  • Keep the cans only upright with the valve up.
  • Once opened for use, the can for gun should be used within four weeks.
  • Cans containing product at high pressure. Do not pierce or burn cans, even after their discharge.
  • If plastic tip is stuck to the adapter of the gun, do not use force to loosen it, because there is threat to break the valve and this will lead to uncontrolled release of material from the can.
  • If extrusion is difficult not attempt to damage the can to get the foam from him forcibly.
  • Do not direct the stream of foam to humans, animals, plants and other living organisms.

Technical Data Sheet Technical Data Sheet
Material Safety Data Sheet Material Safety Data Sheet
Package 12 х 750 ml. gun can
12 х 750 ml. can for handwork with reusable valve
Expiration date
12 months from date of manufacture

Video

VN:F [1.9.22_1171]
Rating: 8.0/10 (2 votes cast)
VN:F [1.9.22_1171]
Rating: +1 (from 1 vote)
INSTA STIK - Construction adhesive in the form of PU foam, 8.0 out of 10 based on 2 ratings

Permanent link to this article: http://masterlinebg.com/en/?page_id=925

Flags Widget powered by AB-WebLog.com.